- Vcds 12.12 connection problems install#
- Vcds 12.12 connection problems update#
- Vcds 12.12 connection problems driver#
- Vcds 12.12 connection problems windows#
in 11.11.5 ROMANIAN is not possible to made LC for an Can GWġK0-907-530-V1.clb exist in LAbels and in Labels\ROJ I understand that if the cable have been banned then in info there will be unregistered is that right?Mine is fully registered.I see today that when i put test interface i have k1 ok k2 ok can not ready.I tested on golf 5 with can bus protocol.Maybe i hav defective can chip?Can i try one A82250 before i reflash the cable?ī.e.
More credible is "RossTech internet contact")Ī.the 11.2.0 are for older version, 11.2.0, forget it. IF they don't lied to me.can be a trigger in programm more powerfull like "soft is out of date" for unregister the interface (if is OEM and must update, why don't update? aaaaaah, is a clone? can be an explanation of selfunregister but only a possible explanation theoreticly. I don't know if is real but few persons told me that without internet when tested a new car, from 2013.2014. If you do this OK and not working.something is defective. uninstall and reinstall VCDS-Release-11.11. must working. The last let as is.or can check and write FFFFFF56.Ĭonnect the four wires for data and + and - 12V on OBD2 pins 16 and 4, write the atmega uc. choose flash.fle open eeprom file choose bites from left to right CD DC F9 FF and select all first four checkboxes. In ExtremeBurner choose atmega162 file open flash. hex as type for save ) and save as eeprom eeprom.hex. If use an USB AVR programmer with eXtremeBurner.in Ponyprog load dump.bin as OPEN DEVICE FILE and save two files in File->save as flash file (. If you use ponyprog for rewriting, you need to have LPT native port or, PCMCIA LPT port.
Vcds 12.12 connection problems driver#
How do you recognize which version XX corresponds to a particular xx.xx.xx software and how do I uninstall driver only without uninstall whole program?į MProg to reprogramm the FT232BM you have.ĭump.bin =flash and eeprom in the same file. That because of "history" of protection.was protection with STC, was broken.etc.Īs usual very good explanation and really useful comment liviudiaconu, but I have a particular doubt, maybe a dumb one: Is a good solution, but for clones the better solution still remain "on diagnose pc, not internet connection, all network cards disabled". Run VCDS from an external disk (USB stik, external HDD, sdcard.etc).Īfter, remove external disk and reenable internet. My recomandation for using internet is: disable internet connections all. Is possible that RT find the sollution for "bypass" the protection made by "hosts" or by loader and. Try uninstall driver for 11.11.0 (2.08) and reinstall from the folder of vcds (newer version) or (older that 10.6.4).īut, at this time, except the named "HQclone" for none of the rest of versions use internet. The problem can be if have 11.11.0 and 11.11.x, X>=1, because 11.11.0 use a bad version of driver.
Vcds 12.12 connection problems windows#
I never restart windows for run the other version and never had problems. I don't think that working.īut, in the same session of windows i run let say, first 11.11.0, close, run 11.11.5, close.etc.
Vcds 12.12 connection problems install#
Step11: System will search the drive for several seconds, then it will indicate that find the driver and then install it.Īt the same time two versions of VCDS is not ok. Step10: Let the driver point to C:/Ross-Tech/VCDS
Vcds 12.12 connection problems update#
If do not have the pop up window, let it be, Right click "my computer", select " hardware", then "device manager", then "Other device", then right click "USB device", select update drive. System will indication found new hardware, and will pop up window for driver update. Step9: Unplug the cable, and then plug the cable to the USB port. Step8: Save "RT-USB.inf" file and then exit. Step7: In the end of the text, add one more line as " USB\VID_xxxx&PID_xxxx.DeviceDesc="VCDS Compatible USB Interface", the four numbers or alphabets are also the same as the ones you write down in step4. Please ensure the four number or alphabets are the same as the ones you write down in step 4. Step6: In item, please add one more line as " %USB\VID_xxxx&PID_xxxx.DeviceDesc%=RT-USB, USB\VID_xxxx&PID_xxxx", (EXEMPLU:%USB\VID_0403&PID_6001.DeviceDesc%=RT-USB,USB\VID_0403&PID_6001) Step5: Unplug the cable, select" my computer" -"C:/"-"Ross-Tech"-"VCDS"-"RT-USB.inf". VID_xxxx & PID_xxxx, please write down the 4 letters or number for VID and PID. Step4: Right click "USB device", select "properties", select " detail", there will be a line information displayed. Step3: Right click "my computer", select " hardware", then "device manager", then "Other device", the " USB device". There maybe be a pop-up window to indicate you to install the driver, for damaged cable, let it be, skip it. Step2: Plug your disabled cable to the USB. Step1: Please ensure that you have installed the VCDS software. Read and folow next steps.( it is not my tutorial, it is shared somewhere over here on this thread.